HORMANN UAP1 PDF

Find great deals for Hörmann Universaladapterplatine UAP 1. Shop with confidence on eBay!. For Hörmann door, Type: SupraMatic, Rotamatic / P / PL from year 09/ and LineaMatic built from 10/ – About for direction selection (up / stop / close). For inputs to Hormann: does it mean that I have to run 6 wires for this section from Loxone to Hormann? Or is it possible to reuse the wire for

Author: Aragis Gadal
Country: Togo
Language: English (Spanish)
Genre: Health and Food
Published (Last): 10 January 2006
Pages: 413
PDF File Size: 14.90 Mb
ePub File Size: 9.80 Mb
ISBN: 492-1-78424-685-4
Downloads: 59218
Price: Free* [*Free Regsitration Required]
Uploader: Kajizshura

Currently I send a 0. The changed partial opening position is saved. Hardware Top side of the circuit board: Bottom side of the circuit board: Intelligent contol panels As you can see the only status bit set, is from the second byte and means reversing according to homrann patent which makes no sense to me. Email Required, but never shown.

Hörmann Universaladapterplatine UAP 1 | Smolka Tor- und Antriebstechnik Berlin Online Shop

Press the PRG button until the decimal point next to the menu number is illuminated. I expected a rather simple protocoll where no comunication happens until the UAP1 gets triggered by a switch, but I was more than wrong.

Any help would be greatly appreciated. Connect potential free contacts directly to the motor. Not specified in the patent So I decided to reverse engeneer and document the bus! I’ve set two analyzers for async serial data on both, the RX and the TX line. After having discussed that issue with my Italian friend he was able to figure out the polynom 0x07 as well as the initial value 0xF3 for the CRC algorithm.

For that to work I needed to buy a UAP universal adapter, meant for uses like these and connect it to my Loxone miniserver. A message is always formed like this: By ual1 “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that your continued use of the website is subject to these policies.

  ACCIDENTAL CRUSH ADRIENNE TORRISI PDF

Hormann garage door opener automation with Uap11 Ask Question. Whith that one I can tell when the UAP1 is sending and when it is receiving! The description in the patents is not cristal clear at least to me but still extremely helpful in figureing out whats going on on the bus.

Move the door into the desired position with the buttons andvia the taught-in radio code impulse or an external control element with impulse function. Could it be that you 0.

Unfortunately the patent doesn’t say anything about the device codes. These are the messages I was able to make sense of so far.

The only things I get from what is stated is that if you press to open – you press the button again to stop it not a true move up move down motion. Usa a UAP1, a small extension box to have better control over the motor and get some feedback signals.

To change the partial opening position: When the board horkann powered while the logic analyzer is collecting data, we see these bytes comming in:.

I am an electronics amateur and can’t figure out based on the schematic below if that is correct? If the selected height is too low, a 2-digit number starting with 1 will appear with a flashing decimal point see section So I basically want a remotely controlled button the app where I click open and it will start moving up until the end position, which should be possible, and it sometimes does move or open, but something must be off with the connection, impulse duration or voltage as it does not work consistently: Post Your Answer Discard By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that your continued use of the website is subject to these policies.

  IN THE MEANTIME BY IYANLA VANZANT PDF

Not referenced Bit 5: I might misinterprete some of them at this point: The message can be between 1 and 3 bytes long and the patent states that it can be expanded. To control the door via a home automation system you have several options: Pedestrian door Bit 6: But at least I can connect to GND there. Dynamically assigned by the master The slave responds to a status request by the master.

Hörmann Universaladapterplatine UAP 1

That means you have just very basic control over the motor because you can’t give up and down command but just a go command as you can with the radio controls. To dig deaper into the protocoll I need more data. According to the Guide you homrann The UAP enables you to control the light of the supramatic open the garage door close the garage door stop the garage door check whether the door is totally closed or totally open, light status?

That way I’m able to trace the bus in realtime without the need to leave the house It’s pretty cold outside at this time of the year. This question came from our site for electronics and electrical engineering professionals, students, and enthusiasts.

Hörmann Universaladapterplatine UAP 1 | eBay

The CRC checksum After being able to seperate the byte stream into messages, I still wasn’t able to calculate the checksum. In my case the UAP1 answers: The remotes require a 2 second press to avoid accidental presses, have you tried making your pulse longer?

I tried some CRC brute force attempts but without success. That occured at hormann 8N1 so I think that must be the correct baudrate. This is how far i got until now.