SRC Devices DSS41A Explore Electromechanical on Octopart: the fastest source for datasheets, pricing, specs and availability. DSS41A05 Datasheet PDF Download – (DSS4 Series) Reed Relays, DSS41A05 data sheet. DSS41A05 SRC datasheet pdf data sheet FREE Datasheets (data sheet) search for integrated circuits (ic), semiconductors and other electronic components.

Author: Fauhn Dojin
Country: Chile
Language: English (Spanish)
Genre: History
Published (Last): 24 March 2015
Pages: 285
PDF File Size: 1.34 Mb
ePub File Size: 6.45 Mb
ISBN: 310-6-95347-598-4
Downloads: 67764
Price: Free* [*Free Regsitration Required]
Uploader: Nekasa

Toggle Switch chasiss mount. It is a soft start device and does not datasgeet in current slug or arcing effect. When properly protected, the reed switch outperforms most other electromechanical switching.

Datasheet archive on 10-4-2013

The adjustable speed resemble again, the dimmer AC circuit that is presented earlier. This dss41z05 an ordinary fan appliance setup pior to the Traic setup. When your logic depends on positive voltage as a reference to switch on the transistor. The following are some of the common npn and it’s complementary pnp transistor ranging from low to high current ratings.

(PDF) DSS41A05 Datasheet download

More information about using a dss41a50 as a switching device, can be found in the later section ” Transistor ” fig. This is what this page is all about.

The circuit is actually very similar to the dimmer for lighting bulb. You need a pair of wire. The DSS4 was developed several years ago and continues to be the relay of choice for hook switch applications in modems and general purpose applications. I am surprised about the behavior of this AC relay, thinking that a Vac should hold the relay still. For example, an input 3.

DSS41A05 Datasheet PDF –

Using transistor as a switch to drive high current loads fig. All about making a good short circuit. The oscilloscope’s screen capture on the left shows the glitches dataaheet by the following PCB mounted fatasheet push button switch. Always refer to your datasheet for actual component’s specification. The following is a quick guide to getting your triac components.


Introduction to the uses of Mechanical, Electrical and Electronic switches. Compare it with the river flowing down to the sea, the stick is too small to be seen. A switch is a mechanical to electrical conversion device. When do we used it? It is very likely that the semiconductor devices model for example, solid state relay, integrated circuit IC, transistor, that are presented on this page might be already behind time.

The ECE Store provides many services to electrical and computer engineering students in order to create a safe environment in which students have access to the equipment and parts they need. It is a trade off to decide upon. The force is small but is large enough to cause the contact plate to bounce away. I can’t find any history on the evolution of the mechanical switches.

Form A is defined as a normally open switch, while Form B is a normally close. A power meter is plugged onto the incoming power source. A 12V SLA sealed lead acid battery would certainly meet this requirement. The design value for R2 resistor should be considered based on the input devices the switch signal will be feeding to.

Only a wire to the base will not turn the transistor on. The value of R3 should be small enough for Q2 to turn on, big enough such that it don’t burn Q2 or waste too much energy. It is just my guess. It also make tick tack noise produce by the dss41z05 action.

Logic or signal line to be connected to the base. Some part number that you can refer to, for Reed Relay products. Switching speed is considerable faster than a relay because the switch mechanism inside the package is small.


On site deployment will be easier, and system troubleshooting can be a lot faster. A practical des41a05 to remove the signal glitches would be through electronics components and design.

Reed relay is a smaller version of relay. A higher value R2 example: Fortunately it is also easy to understand, if you pay enough attention in this topic. For example, one company may datasheer a robotic application which require mobility and high current discharge. This is non-technical, and is more about user’s experience. This is a very important section. Rather than using a jumper wire to make connection manually, human invented switch to make short circuiting task more efficient.

Leakage current is due to the snubber networks R-C circuit across the output used to dsx41a05 the commuating dss41a5 inductive load. Voltage difference can be more than 0. A mechanical relay current need at least 5V to 24V to enegised the relay’s coil to pull the switch. Datasheef is the trade-off on choosing an appropriate switches. Another one may choose to deploy 5V system, because they have been using some critical component which requires 5V. The resistor is there to absorb all the unapplied voltage, so that Vbe can be maintain at 0.

Low voltage digital input to control Vac relay The circuit examples on the left illustrate my testing, interfacing a low digital voltage to a triggered AC relay. The cable must be thick enough to handle the high current and Vac voltage.