CISCO MDS 9124 CONFIGURATION GUIDE PDF

Example Cisco MDS Switch Default Port License Configuration. switch# show port-license Available port activation licenses are 0. Cisco MDS Family Quick Configuration Guide. OL Using the Switch Setup Utility Verifying the Module Status CHAPTER. 3. Configuring. Note If a Cisco MDS or switch is used as a core switch, only a nontrunking F PortChannel is supported. Trunking is not supported on.

Author: Nikora Tura
Country: Serbia
Language: English (Spanish)
Genre: Relationship
Published (Last): 18 December 2014
Pages: 50
PDF File Size: 20.61 Mb
ePub File Size: 17.27 Mb
ISBN: 372-6-97705-378-6
Downloads: 19234
Price: Free* [*Free Regsitration Required]
Uploader: Zulkizilkree

I am not sure. In this case, using the proxy initiator mode simplifies the configuration.

FCIP uses different ports. If you enabled the autoreconfigure option on both switches before connecting the fabric, a disruptive reconfiguration RCF will occur. Then states two bullets later: If you assign port number for physical portshow can you assign for ports ?

Previous blog entries also dealt with storage, compute, virtualization and professional services. Page shows with 8 base ports 8 licensed for growth. You do not need to restart the fcdomain. The way its written sounds like if you have a large scale deployment where you need explicit LUN access control you can use proxy-initiator, but its really the opposite.

This is not correct. When you jds two switches belonging to two different stable fabrics that have overlapping domains, the following cases apply: Proudly powered by WordPress.

  ANDRES PUEYO MANUAL PSICOLOGIA DIFERENCIAL PDF

A disruptive reconfiguration may affect data traffic.

I am not sure if this is valid. Caution The span drop-threshold can be changed only if no span sessions are currently active gujde the switch.

This page incorrectly states that you can disable password verification with aaa authentication login none command. Page Information is repeated twice on the same page: If a domain is currently isolated due to domain overlap, and you later enable the autoreconfigure option on both switches, the fabric continues to be isolated. This situation can require several configuration tasks for each iSCSI host. The default authentication port is On the same page I find this block of text very vague and confusing: Configutation opinions expressed in this blog are entirely my own and should not be taken as the opinion of my employer.

Page Document states: This md incorrect states that fcns reject-duplicate-pwwn configuratjon disabled by default. About System Message Logging properly configured system message logging server. The autoreconfigure option mss immediate effect at runtime.

Should say Step 1 Enable the mgmt 0 interface. Have a few different people read that and I think you will see where I am coming from. These pages talk about an active mode of fcanalyzer. Although it can be configured it has no effect.

Unofficial Cisco MDS Release 3.x CLI Config Guide Errata – Maximum Entropy

Testing indicates that this is in fact enabled by default. This however would be very nice to have in the documentation for IPS network simulator, an example showing complete configuration of Gigabit Ethernet interfaces and FCIP tunnels to go along with the Network Simulator.

  GESUNDHEITSMONITOR 2008 PDF

Reconfiguration as in changing of domains is always disruptive. IP routing does not have to be enabled, unless there is a specific topology where IP routing is necessary. You basically give the same settings for the Confiburation blade switch but this is a 24 port not a 20 port.

Unofficial Cisco MDS Release 3.x CLI Config Guide Errata

This is not true. Cisco Documentation team has internally re-written this as: Leave a Fuide Cancel reply You must be logged in to post a comment.

This should be made more clear. Page Figure shows incorrect ip default-gateway Page States in one bullet: You can nondisruptively reconfigure the fcdomain by changing the configured domains on the overlapping links and getting rid of the domain overlap. If you do not need explicit LUN access control, using the proxy initiator mode simplifies the configuration.