ASTM A682 PDF

ASTM A Standard Specification for Steel Strip, High Carbon, Cold Rolled, General Requirements. Find the most up-to-date version of ASTM A at Engineering ASTM A, AM – Designation: A /A M – 02 An American National Standard Standard Spe.

Author: Samurisar Kajinris
Country: Argentina
Language: English (Spanish)
Genre: Software
Published (Last): 20 March 2007
Pages: 135
PDF File Size: 6.67 Mb
ePub File Size: 12.78 Mb
ISBN: 911-9-86318-295-3
Downloads: 1786
Price: Free* [*Free Regsitration Required]
Uploader: Samule

Two additional samples are secured from each end of the coil from which the original sample was taken.

Asttm edition approved March 10, C Number 3 edge strip with thickness tolerance guaranteed at less than 3? This is produced when the edge condition is not a critical requirement for the?

Combining values from the two systems will result atm nonconformance with the specification. Number of Tests and Retests However, unless the order specifies the applicable “M” specification designation SI unitsthe material shall be furnished to inch-pound units.

Conformance to SI tolerances is mandatory when asrm “M” specification is used. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Unless otherwise agreed to, all tests and inspections, except product analysis, shall be made at the place of production.

The elements comprising the desired chemical composition are speci? The values listed are not exact conversions of the values listed in the inch-pound tables but instead are rounded or rationalized values. Thickness Tolerances Plus or Minus, in.

Dimensions, Mass, and Permissible Variations 9. However, unless the order speci?

ASTM A682 Grade 1074

However, under SI the preferred term in mass. The ability of manufacturers to meet the maximum coil weights depends upon individual mill equipment. Within the text, the SI units are shown in brackets.

  CHIONE CALIFORNIENSIS PDF

B Measured 10 mm or more in from edge; and on narrower than 25 mm, a6682 any place between edges. Each of the elements listed sstm Tables 2 and 3 and additional elements agreed upon by the purchaser and the supplier shall be included in the report of heat analysis.

Notwithstanding the absence of a signature, the organization submitting the EDI transmission is responsible for the context of the report.

Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. For strip length under 8 ft. When required, minimum coil weights are subject to negotiation. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm.

NOTE 2—Camber tolerances as shown in the table are for any 8 ft. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.

Combining values from the two systems will result in nonconformance with the speci?

ASTM A Steel, Strip, High Carbon, Cold Rolled, General Requirements

This edge is produced when the width tolerance and edge condition are not as exacting as for No. For strip length under mm, camber tolerance shall be subject to negotiation. This specification covers the general requirements for cold-rolled carbon spring steel strip in coils or cut lengths. Strip tolerance products may be available in widths wider than ? NOTE 2—The industry de? Stay on Page Continue to Compass.

Originally published as A — The strip may be subjected to product analysis by the purchaser either for the purpose of verifying that the chemical composition is within speci? Combining values from the two systems will result in nonconformance with the specification. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other.

  CRAFTSMAN 25188 PDF

Normal coiling or piling does not provide a 3 Where an ellipsis. When agreed by purchaser and supplier, other silicon ranges are permissible. When the maximum manganese limit exceeds 1. The material must be adequately protected and correctly identi? Finish and Edges The values stated in each system are not exact equivalents; therefore, each system must be used independently of the astj. However, the document shall clearly identify the organization submitting the document.

If you feel that your comments have not received a fair hearing you should make your views asmt to the ASTM Committee on Standards, at the address shown below. The values listed are not exact conversions of the values listed in the inch-pound tables but instead are rounded or rationalized values. Conformance to SI tolerances is mandatory when the “M” specification is used.

NOTE 1—Camber is the greatest deviation of a side edge from a straight line, the measurement being taken on the concave side with a straight edge.

Revision to Table 2. This standard has been approved for use by agencies of the Department of Defense. However, unless the order specifies the applicable “M” specification designation SI unitsthe material shall be furnished to inch-pound units. When the amount of vanadium, columbium, or titanium is less than 0.