2N7269 DATASHEET PDF

n Light Weight. For footnotes refer to the last page. IRHM REF: MIL-PRF- / TOAA. This datasheet has been downloaded. 2N 2NU. JANSR (K RAD(Si)). JANSF (K RAD(Si)). ABSOLUTE MAXIMUM RATINGS (TC = +25°C unless otherwise noted). Parameters / Test. 2N datasheet, 2N pdf, 2N data sheet, datasheet, data sheet, pdf, Microsemi, N-Channel.

Author: Zulkinos Virr
Country: Paraguay
Language: English (Spanish)
Genre: Love
Published (Last): 16 June 2006
Pages: 458
PDF File Size: 19.29 Mb
ePub File Size: 5.69 Mb
ISBN: 414-6-96096-134-6
Downloads: 44334
Price: Free* [*Free Regsitration Required]
Uploader: Jugami

2N7269 Datasheet

Mag netics also ofTers unique capabilities in the design and manufacture of spedalized components fabricated from magnetic materials in many sires and shapes. Ref- ” 1 Tin plated finishes. The type of insulation consists of a two digit codes The type will be defined on the specificationsheet. Thickness shall be 2 54 pm to micromches 7.

For further information write for ‘dialog TWC AD core sizes ran be provided in non- metallic phenolic or plasticaluminum, or CVB Guaranteed Voltage Breakdown coated aluminum boxes. Detailed finish requirements for each of the electrical parts.

Composition shall be 50 to 70 percent tin remainder lead. The type of insulation consists of a two digit codes. The specified lead composition see 12 1. Use of tin plating is prohibited as a final finish and as an undercoat see 6 8. These alloys are attractive for magnetic core devices where rug ge dues s and low weight are important.

Silver-coated coppe r wire. Jsf 1M0PM Finish 31 is no longer available on the current revision of the specification. Pure tin may not be used to coat any surface see H 4. Smallest sizes miy not Ctt wtrudaWe rt certain matenils. Thesr components are available in square configura- tions with outside dimensions of approximately.

  CARULLI OP 96 PDF

Parts that have the finish verified during Destructive Physical analysis on sample parts. Consists of the tetter M. The device claee ahell be detipwtad by a single latter idwitifying tha quality 3.

Thickness shall be 7. The wire type is 05, gold plated; 0.

2N Datasheet pdf – N-Channel – Microsemi

C – Datqsheet solder dipped 60 microinch minimum. Cores are available in all IEEE standard sizes and over 1, special sizes. DPA report 1 identifies the package as ceramic with no tin platting, see following insert. Magnetics Dahasheet Yes 3. A pure tin finish is not prohibited. Parts that do not specify the lead finish or specifically prohibit the n27269 of pure tin as a finish. Following these tests, the manufacturer shall dataxheet the lot to the group A solderability test as specified in 4.

Biro copper wire shall c anfom to soft or annealed copper wire In accordance with AST Flux shall be of such a quality as to enable the film resistors to meet ail the requirements of this specification. Parts procured to a Military Specification with a QML listing qualified parts that have a statement that prohibits the use of pure tin and defines dztasheet finish as part of the part number in the Military Specification.

The final finish for leads see 1. Flux shall be of such a quality as to enable the resistors to meet all the requirements of this specification. The inductors are open coil E. The data sheet does not specify the material finish of the package or the leads. The case for these capacitors is multi- layer, unencapsulated, monolithic. I SEM anomalies if applicable. Where space is critical, the low profile CLP component should be considered, but at the expense of some reduction in electrical Q.

B – Gold plated 50 microinch minimum. When specified, under-plating shall be in accordance with 5 dagasheet 1. The lead finish ehaii be designated by a ainple letter aa toilowe: Use of tin-lead finishes are acceptable provided that the minimum lead content is 3 percent. The following DPA report,identifies the package as gold plated. Use of tm-lead finishes are acceptable provided that the minimum lead content is 3 percent.

  ARTICULOS DE DIABETES INSIPIDA PDF

Foftowmg too sufder dHi retmning process the etectncai measurements required hi group A subgroup ” pnrcenl screening test Stiafi be repeated on percent of tori lol.

Ratasheet sizes are available from stock. Use of tin lead finishes are acceptable provided that the minimum lead content is 3 percent.

For glass- to -metal sealed products, 2b7269 devices with terminals which are solder dipped to the seal shall pass screen 7 of table IV. Description Part Value 1.

IRHN MOSFET Datasheet pdf – Equivalent. Cross Reference Search

Silver-coated copp er-cl a d steel wire. Capacitors covered by this specification are classified by style as specified see 3 1 1. The number indicates the nominal percentage, by weight, of the component element s see 3. The use of pure tin plating is not prohibited in the drawing and the package finish is not specified.

The termination finish is identified by a single letter as follows: For glass -to- metal sealed products, all devices with terminals which are soldef dipped to the seal shall pass screen 7 of table IV, appendix E with a sample size of 1 16 pieces no failures allowed c. Wound on nonmagnetic stainless steel bobbins, core diameters are available down to 0.